dual_sport_dork 🐧🗡️

Progenitor of the Weird Knife Wednesday feature column. Is “column” the right word?

I make knives now, too. Why not buy one at flightlessforge.com?

  • 1 Post
  • 16 Comments
Joined 3 years ago
cake
Cake day: July 20th, 2023

help-circle
  • I was originally going to make a pithy comment here about how televisions never derived their sync frequency from the mains because I know full well that the sync pulse for analog television is sent along with the video signal from the transmitter and the TV is slaved to it. In the absence of this TVs from my era had their own oscillators that generated the appropriate sync frequency which may or may not have been in phase with the frequency of whatever it was they were trying to receive, and thus also a sync splitter circuit that attempted to switch the start of frame to be in lockstep with either the sync pulse from the station if it was strong enough and the internal timing when it wasn’t. The whole point of this was to be able to display at least some manner of intelligible image to the user as an aid to getting the station tuned in.

    But then I remembered a key phrase there, which was televisions from my era.

    (This is all just whiffling and is completely irrelevant to photography, so everyone who isn’t specifically interested in this rather off-topic diatribe is encouraged to ignore it.)

    I had apparently blocked out the memory that prewar television sets in fact did derive their frequency from the mains. As it happened this turned out to be exactly as stupid of an idea as you think it was. Foremost isn’t actually the obvious consideration that the mains frequency isn’t all that accurate to begin with, but rather it’s the fact that it is spectacularly unlikely to be in phase with the frequency of whatever transmitting tower your TV is listening to. One which would of course be any arbitrary distance away, and not even guaranteed to be on the same grid. These interactions resulted in the appearance of “hum bar” artifacts on your screen where the refresh cycles didn’t quite line up. Sometimes these could be tidied away into an inconspicuous or even off-screen area with careful tuning (compensating for this sort of thing is part of what the old vertical and, ye gods forbid if we’re going back that far, horizontal hold knobs on old television sets were for), but if you were particularly unlucky due to wandering frequency timings they’d be rolling up and down your screen constantly.

    Obviously the entire industry was keen to do away with this nightmare as soon as it was technologically feasible, and when transistors came about they sure did.

    Once NTSC color came along they didn’t have a choice anyway, because the cycle frequency of color television isn’t 60hz like the mains anymore. In order to leave room — or rather time — for the colorburst signal, the frequency of not-actually-modern-anymore NTSC television is actually 59.94hz. So if you’ve ever wondered where that weird frame rate still available in all your video editing software comes from, now you know.


  • That doesn’t mean that Sony didn’t deliberately jigger it to stop at the 4 gig mark for compatibility purposes, or equally likely apathetically fail to change prior legacy code/firmware not to do so in specific circumstances. The key word from the above commenter there is expecting FAT32.

    The penalty for attempting to cross that mark when a user doesn’t happen to have an ExFAT formatted card in their camera is probably to corrupt the file, certainly at least the last segment of it. One which by definition the user just spent quite a lot of time recording.

    If you format the card in the camera, does it format it as ExFAT? And does it to so for all card sizes, even the small ones? The documentation I found online suggests that it doesn’t, but obviously I don’t have that particular model in my hands to test. I figure you would be in the best position to know, there.


  • I waited a bit to put a top level reply on this because I wanted to go home and mess with my selection of cameras to ensure I wasn’t grossly misremembering something and I didn’t have any of them on me at work. For shame, for shame, I know.

    Here is the headline that matters: I, unlike many of the commenters here, am going to freely admit that any speculating I do here is me completely talking out of my ass. The truth of it is that we will never know the actual answer for this quirk except in the unlikely event that a Sony engineer happens to pass by our humble community or possibly if somebody manages to corner one of them and nail him down to an answer somehow.

    My take on the matter is that the forced card reformat smells like an artificial limitation and is either likely due to some combination of Sony flavored ineptitude and/or apathy, or is equally likely to be a deliberate and completely on brand customer hostile action on their part in true Sony tradition. Most likely as some manner of limp-dicked attempt at content region locking.

    You know, coming from the guys who are infamous for being instrumental in insisting that region locking must be written right into the DVD specification, among other things, over and above the inherent NTSC/PAL/SECAM incompatibilities already inherent in all of those flavors of gear.

    I would 100% believe that the camera is not capable of outputting NTSC video when it’s in PAL mode and vise versa for some manner of obscure technical or software limitation. Locking out the video frame rates that are incompatible with your region likewise makes sense, even if only to not give the user enough rope to hang himself. And with the best will in the world, unless the user is deliberately hooking their camera up to some manner of multisync display device it’s not going to work if you plug it into something from the wrong region anyway, especially if you’re doing it over composite.

    But the formatting your memory card thing feels like one of those extra special Sony flavored fuck-yous, right up there with rootkits on their music CDs, MagicGate… hell, even SonicStage, and all the rest of it.

    So for the record this is a Canon household. I do not have a kind spot anywhere in my heart for Sony and for myriad reasons I never will.

    However.

    My ancient Powershot SX130 IS: Allows me to freely switch between NTSC and PAL, right there in the menu. When I exit the menu, it is already active. No reboot required, no reformat required.

    My R10: Again allows me to switch between NTSC and PAL, right there in the menu. No reboot, no reformat. This camera can output externally solely in HDMI, for whatever it’s worth.

    My EOS 40D: Wouldn’t you know it, this also allows me to switch between NTSC and PAL. No reboot, no reformat. But the sole effect this has as far as I can tell is changing the flavor of the analog video output via the barrel jack on the side.

    Just for grins I took a short video clip of the blinkenlights inside my computer tower with both my SX130 and my R10 in NTSC mode, then switched to PAL and checked if I could play it back. The answer is yes, no problem. (And the 40D actually doesn’t have a dedicated video mode, believe it or not, so we don’t get a third data point.) The R10 does change its offering of recording frame rates depending on whether you have it set to NTSC or PAL, but the SX130 is not that complicated and doesn’t allow you to change its inbuilt video framerate, resolution, or aspect ratio at all. But it still works either way.

    So in the absence of a first hand source, we can describe it thusly: Incompetence, indifference, or malice. Pick any three.


  • because WTF is limiting MP4 to 4GB

    The answer is 32 bits. Any time you see that 4 gigabyte wall it’s either related to a 32 bit FAT32 file size limitation, or a 32 bit byte counter somewhere running up against its limit. 2 ^ 32 = 4,294,967,296 which is 4 gigs on the nose if we’re talking that many bytes.

    The online scuttlebutt I found indicates that this camera only officially supports the FAT32 filesystem and while it “can” read and write an ExFAT formatted card if said card is formatted externally, it’s not officially supported and Sony says there is “risk of data loss.” The camera itself will not format a card to anything other than FAT32, with all of the limitations that entails.

    One of which is 4 gig files.



  • What this commenter wrote almost makes sense if this camera were an oldschool analog device, think the era of tape camcorders and VCRs and so forth. And tube televisions and even the retro game consoles connected to them, for that matter. These machines were all heavily tied to the frequency and timings of their native video signal format, either NTSC or PAL (or even SECAM, if you want to get really obscure).

    This is absolutely not the case with a modern flagship mirrorless camera like the Sony ɑ7RII in OP’s picture. It is obviously not only eminently capable of altering its shutter rate, sensor refresh speed, and video recording frame rate to any arbitrary value but is purpose built to be able to do so. The only part of its componentry at all that is operating at NTSC/PAL frequencies at any point is whatever tiny amount of DAC hardware it’s using to output that low-def TV signal (probably composite video) out the little barrel jack on the side, and even then only when you’ve got it plugged into an analog TV.

    Analog NTSC and PAL are very different from each other. Digital “NTSC” and “PAL” (in reality there’s really no such thing) are not. The block of NTSC countries have TV’s that expect a 60hz frame rate and those in traditionally PAL countries expect a 50hz frame rate. That’s literally it.

    The following claims are bogus:

    You can fake the video with just the framerate

    No, that’s literally what digital HD video does nowadays, like the type you’d transmit over an HDMI cable.

    implies the entire electric circuit ran at a specific frequency

    This was true for analog devices and those whose timings had to be tied to the output frequency, but is not the case for a digital device that handles all of its signal processing internally.

    Which is easier to do if everything inside the camera, shutter, pixel refresh, encoding, etc. runs on the same frequency.

    This is not even remotely what a high end modern camera does. Sony is obviously mum about the exact specifications of the “Bionz X” main image processor in the ɑ7RII, but it is obviously a modern highly specialized chip most likely running at many hundreds of megahertz, completely independent of the camera’s external video output.

    If the camera can be fed with direct power it will also condition the internal components frequency.

    I think this grammatically malformed statement is trying to imply that the camera must run in lockstep with its input power frequency. If so, this could only be true if the camera were an analog device running directly off of mains current from a wall outlet. This is not so for any digital camera; they’re DC devices primarily fed from their battery which obviously has no electricity frequency and secondarily if they’re externally powered this is also through DC from an AC to DC step down converter. No part of the mains voltage frequency should be making it to the camera. If it did, this would be very bad. Smoke would certainly be involved.

    Furthermore, the mains voltage frequency is not nearly accurate or consistent enough to tie the operating frequency of any electronic device to it. You can easily observe this with oldschool analog clocks which derive their drive speed directly from the 50 or 60hz frequency of their mains power supply; they don’t keep very good time. So electronic devices even if they ostensibly “run at” their countries’ analog TV frequency at 60 or 59.94 or 50hz or whatever still use their own internal crystal oscillators to create that frequency accurately rather than blithely relying on the mains frequency.

    If it is for sync when recording screens or using old lights, the entire camera must run on the same frequency, or the skip when faking framerates is actually still noticeable.

    Once again it is trivially verifiable that this is not so; I have point and shoot cameras from the early 2000s which can change both their flash sync and screen sync settings on the fly with no ill effect, no reboot or reformat required, and the results are clearly visible. Anybody with a camera in their hands could verify this in about four seconds without having to resort to spouting any bullshit.

    All this would require restarting the electronics to run on the correct frequency.

    No, it just requires setting the recording framerate to the correct value and optionally tuning to start the frame exposure at the correct time. Which again, any competent digital camera can already do.

    The old encodes go beyond just containers, they do bitwise manipulation as well. Electrical system agnosticism is a modern result of newer container formats.

    This is either willfully or ignorantly conflating the way that analog and digital video encoding work, with a sprinkling of buzzwords thrown in for good measure.

    (Edits: I fixed a spelling error and removed a duplicated couple of clauses.)



  • Your phone is also visibly applying a ridiculous amount of postprocessing to that image to make it appear “smoother,” applying a layer of paper mâché over the shortcomings inherent to its tiny pinhole lens and sand grain sized sensor that you probably can’t turn off.

    Let it not be said that I will ever deride somebody just for taking a photo with their phone, because I’ve certainly taken plenty in my life. Not even just because my phone was all I had to hand but even on purpose. And employing heroic amounts of effort to do so without the final result being crap.

    I only take exception to the occasional type of blissninny who regularly feels compelled to spout off in the comments that cell phone cameras are “just as good” as our big expensive pointless cameras for applications where the bringing more than one brain cell to bear on the topic would make it glaringly apparent that they absolutely are not, e.g. long range wildlife photography. The strides cell phone cameras have taken over the years are indeed impressive, but they still cannot violate the laws of physics no matter how glossy Apple or Samsung’s marketing materials are.



  • Discovering that their hardware suppliers have only ever used them for their money has seriously hurt their egos and broken their brains.

    I get what you’re trying to say here, but this part is literally just how retail works. I pay you money, you give me the goods I want, and the money I pay you enables you to stay in business producing whatever it is for when I need another one.

    I think basically the entirety of Nvidia’s leadership could be pushed into a volcano and the average value of humanity would slightly increase. But expecting their operation to be some kind of charity is a bit silly.

    The major thing that us capital-G gamers have been pissed about, and rightfully so, is not only Nvidia’s rather well documented abuse of its consumer side customer base for a very long time but also the fact that they’re functionally the only game in town for a lot of purposes. Now it turns out that this is for completely artificial reasons, i.e. Jensen Huang formerly of Nvidia and Lisa Su of AMD are literally blood related to each other and privately agreed not to compete with each other in the high end consumer GPU market. So by design there isn’t even any competition. AMD “wins” in processors and Nvidia “wins” in video cards and both of them can therefore just charge whatever the fuck they want. That is indeed some bullshit.







  • 4 into 1, yes. The bits in between are the layer behind it, and the aspect ratio is actually such that they two layers can interlock into each other like Velcro, which is certainly interesting. I haven’t quite decided yet if it will actually graduate into being annoying. These are 12 gauge aluminum at a 3/8" inner diameter.

    This is my third suit, or it will be after I’m sure several more weeks of careful jeweler’s sawing and ring bending. I have a full set of steel chain with 12 gauge 1/2" links as I have sporadically vouchsafed before. And when I say “full” I mean full, because I also took it upon myself to make a coif as well as a deeply anachronistic pair of chain pantaloons with even less historically accurate Nylon suspenders for them. That’s taking up an entire milk crate in the basement at the moment and desperately needs a polish before I show it off to anyone.

    I also made a set of the same consisting of just a hauberk and a coif for my uncle, who is a retired history professor. He’s super into medieval stuff, but somehow never got around to accumulating the collection of swords, armor, bows, etc. that I did. I’ll never fathom how.

    The current project was brought about by the desire to have something lighter, I suppose for lack of a better description, for exhibition purposes.

    Edit: I tell a lie. It will be my fourth set. That’s because I completely blocked out the memory of my hexagonal pattern “Japanese” style mail vest I made years ago as well, possibly down to its wire cutter made links being specifically oriented to be extremely annoying catching on everything every time you put it on or take it off.

    This is of course completely aside from the various bits of chain jewelry, cuffs, bracers, and gloves I’ve made over the years. Eventually I’ll shine some of those up and I’ll have to post pictures of them, I suppose.